Or you could release the pressure with the release valve on the fuel pressure regulator under the hood. Also a explanation of what tools are needed. Be sure to use safety stands for your protection. How to replace Chevrolet Impala fuel filter from 1999-2004. The video above, shows you where the engine air filter is located in your Impala and how to change it! On my 2004 Cavalier it is in front of the gas tank under the body. Keep a good sized drain pan handy, keep any items away that could cause a spark or flame. Your 2002 Chevy Tracker 2wheel drive and 4wheel drive are the same with the 2.
Some years differ but it will be just before or after your rear tire on the inside of the frame on the drivers side. Check for any fuel leaks in the system before starting. You should change the filter on your Impala at least once a year or every 20,000 miles, whichever comes first. Posted on Apr 07, 2011 check fuel pressure regulator for fuel in vacuum line ,check fuel filter , and alot of those models needed a top engine clean where u drip top engine cleaner through the air tube to clean valves. Insert the new filter in the bracket, put the pipeline back on and attached it back to the car by tightening the bolt back on. He also writes detailed automotive tutorials. If it is the 4 c ylinder when you open the hood it says at Autozone.
This will help to ensure the car stays running at peak performance at all times. Regardless it is the same concept. Here is a simple process that will walk you through a few steps that will pinpoint the overheating problem on your 2003 Chevrolet Tracker, without even using any tools. I wrap a shop cloth around the fitting when undoing it. In addition to improving the fuel economy of your Impala, regularly replacing your air filter will put less strain on your engine. Repeat the process for each remaining wire.
About the Author This article was written by a professional writer, copy edited and fact checked through a multi-point auditing system, in efforts to ensure our readers only receive the best information. Drivers side, underneath by rear, in front of rear tire. Use a screw driver and pliers to unbolt it from the frame. If the clip breaks, you'll have to buy a new fuel line to replace it. About the Author Allen Moore's career includes awards in poetry and creative fiction, published lyrics, fiction books and nonfiction articles as well as a master certification in automotive service from the Ford Motor Company. The filter is mounted inside the frame rail just ahead of the fuel tank. Twist the boot until it comes off.
As a preventive action, it is wise to often maintain your automobile in before and after travels. Make sure the wire snaps into place. These fuel filters are less costly and work just as well, if not better than a stock fuel filter. These filters are fairly inexpensive, so check out our page for great deals and coupons on a new one tip: buy several, when you go to check the filter on your Impala, you can easily swap it for a new one if it is dirty. Then unscrew the other side. Dec 17, 2015 Passenger side, undeneath, next to fuel tank.
This helps us insure you received the right help. It has the filter in the gas tank and is not serviceable. The solution to these problems is replacing the fuel filter. What you need to do first is the unclip the connection. The filter will be just in front of the rear axle.
Lubricate the boots and terminals with dielectric grease and install the wire on the coil pack. Normally this is on the passenger side wheel well or just inside the engine compartment. Allow the fuel pump to run for three seconds. Should you need further help please just ask. Thank You for using FixYa. Be cautious changing it because there is pressure in the lines.
The hinged side clip needs to be straightened out so the you can pull the filter pipe out. Disconnecting the negative battery prevents explosion and flammability danger because where there is no spark, there can't be an explosion. Shut down the engine and insert back the fuse. His expertise in the automotive industry has given him the skills to write detailed technical instructional articles. See picture of sensor below some models has a 45 degree connector, most are straight like the one pictured below. You may have to apply quite a bit of pressure if they are in there tight.