Check to see that all vehicle entrances are closed securely. Although at times you may experience range greater than that, there may be occasions when range is less than normal. The courtesy light will turn on for 1 minute, or until the vehicle is started. Test all remote transmitters to ensure that they work properly. The system will respond with three 3 chirps and three light flashes, indicating that the lite-touch feature is disabled.
Note the chart below: If the Status Indicator is. If the correct code is entered, the siren will chirp twice, indicating entry into the Transmitter Programming Mode. Register a Free 1 month Trial Account. All entrances protected Opening any door or entrance protected by the security system triggers the alarm's 125db siren and flashes the vehicle parking lights. Code Alarm Manual For Ca110 can be very useful guide, and code alarm manual for ca110 play an important role in your products.
To by-pass the alarm system; 1. Conditions of the Theft Protection Program: The Theft Protection Program is non-transferable and non-assignable. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. Be sure to remember your code and keep it in a safe place. The system is now fully armed. Pry off the back of the transmitter and expose the battery. The status indicator will also flash rapidly.
It is not necessary to re-program the remote transmitter after changing the battery. Illuminated Entry Vehicle courtesy lights turn on for one minute when the system is disarmed. The sensor will be enabled the next time the alarm system is armed. After 25 seconds, it will blink steadily, once per second. Personal Protection Panic Alarm Pressing any two buttons together on the remote transmitter activates the Panic feature, sounding the siren and flashing the parking lights. Panic is designed to bring attention to the vehicle and surrounding area, warding off a would-be intruder. Limited Lifetime Warranty A Code Systems Inc.
If the code is lost, it cannot be recovered. After two 2 seconds, the status indicator will begin flashing for Code Entry. The receiver inside your vehicle security system and the remote control transmitters are designed together to have an average operating range of 50 feet during ideal conditions. Each transmitter has a moisture-resistant case and sealed rubber buttons to protect the internal circuitry and 12-volt alkaline battery. The first number has been entered. Interior Status Indicator The bright-red warning light is an effective visual deterrent to a would-be thief. Adding Remote Transmitters to Your System Your security system has the ability to operate from up to four 4 remote transmitters.
The alarm will sound when the door is opened. Note: If you enter an incorrect digit, turn the vehicle ignition off, then on. This is useful when servicing your vehicle. Do not start the vehicle. Consult your installing dealer for options that may have been installed and are not listed. Follow the instructions below to change the remote transmitter battery. Under no circumstances should this warranty, or system covered by it, be construed as an insurance policy against loss.
Note: As a security measure, the security system will automatically exit Valet mode if the vehicle ignition is turned on and off more than five 5 times. To exit Valet mode, press any button on the remote transmitter. Repeat the procedure in steps 3 and 4, this time using the second number in the code. See your installer for details. The status indicator will turn on. Follow the Code Entry Procedure.
Press any button on the remote transmitter to turn off the Panic alarm. . Using Your Remote Transmitter The remote transmitters included with your security system are high-quality, durable instruments. The status indicator will flash twice, indicating the system is in Valet mode. Code Entry Procedure This security system utilizes a secret code for adding or deleting remote transmitters, changing system options and disarming the alarm if the remote transmitter fails to operate. When the status indicator begins to flash, re-enter the code from the beginning. Emergency Disarm Procedure If your remote transmitter fails to operate, the system can be disarmed using the alarm code on the front of this manual.
The 4 digit code should be written on the front of this manual by your installer If not the code is found on a sticker on the back of the alarm module Below is the procedure for entering the code. See your installer for details. The problem is that once you have gotten your nifty new product, the code alarm manual for ca110 gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Impact Detector The impact detector senses any jolts or bumps associated with vehicle intrusion. The doors will also lock at this time if equipped and connected. Follow these instructions to add a remote transmitter to your system. Additional Immobilization Circuits With Select Systems In addition to disabling the vehicle starter when the alarm system is armed, two additional circuits allow disabling of other vehicle circuits such as the ignition , greatly enhancing security.