Check whether the gears can be engaged. Remove the ball and the spring below the shift drum. Note that their pointed edge must be oriented to the outside, i. Mount the carburetor to the intake manifold and to the suction hose of the engine air cleaner box. Grease the shafts and join both crankcase halves with soft tappings by a rubber-headed mallet. Check the intake manifold for crackings and fissures.
The problem is that once you have gotten your nifty new product, the cpi sm 50 workshop manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Pull out the pinion gear and remove the circlip under the pinion gear. Cpi Sm 50 Repair Manual can be very useful guide, and cpi sm 50 repair manual play an important role in your products. . Check the cover gasket for aging or damage. Note that the bearings must not rotate during the cleaning with compressed air. Grease the thrust ring 0.
Keep the spanner in place and loosen the nut with a 17 mm spanner. Mount the key and the balance gear to the countershaft. Check the driving Rubber-lipped seal tab for wear. Lubricate the piston rings and the ring grooves with a small amount of two-stroke oil. For this purpose a universal tool shall be used. Remove the parts in the following order: Clutch drum Clutch gear clutch drum,. Dell'Orto Level adjustment Mikuni Measure the distance between the reference edge.
The cooling liquid has to be collected in a suitable vessel. Register a Free 1 month Trial Account. Measure the resistance with a digital multimeter: Check Cable color Value. Heat up the bearing seat of the countershaft bearing to approx. Save the setting by pressing down the mode button for approx.
The following parts always have to be replaced prior to reassembly. Loosen the lock nut of the adjusting screw. Do not drop relays, sensors, or other electric components and do not expose them to vibration. Slightly move the piston rings to the left and to the Positioning spigot right while watching the position spigots. Cpi Sm 50 Workshop Manual can be very useful guide, and cpi sm 50 workshop manual play an important role in your products. In case of any defects in this part, the float shall be replaced. Electric component parts built in the microcomputer or relay are sensitive to heat and can easily get damaged.
Remove the fuel line, the carburetor heating, and Carburetor the oil lead. The pump body and the delivery line which leads to the carburetor must be bleeded subsequent to the reinstallation. Many proceedings, techniques, tooling and components are known for the various maintenance works that are required for a vehicle, and the knowledge of motor vehicle technicians differs likewise. The ovality of the tread must be below the given limit value. Register a Free 1 month Trial Account.
The problem is that once you have gotten your nifty new product, the cpi sm 50 repair manual gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Screw the puller in the threaded seat of the rotor. The wheel size can be changed by short tappings on the button. Check the cable grommets for fissures and aging. Before maintaining the carburetor, the engine, the fuel supply, and the ignition system have to be in a faultless state. Then unhook the control cable from the slide valve. Loosen the fastening screws and remove the pump casing.
Remove the chain pinion gear. Rotate the inner ring of the bearings with the finger. Verify the seat of the grommets. Compensate the distance with a washer if required. Mount the float chamber cover to the carburetor body. The carburetor can only properly adjusted and faults in the carburetor system can be detected when there are no mechanical defects in the engine or defectas in the fuel supply or in the ignition system. When engaging the gears, they must not jam.
Pay attention not to damage the threads. Remove the rotor with a properly dimensioned puller. Take measurings at several areas of the tread, each staggered by 90°. This position can achieved via the adjuster that is located on the end disc plus the use of a suitable screwdriver. Plastic cover Mounting bolts After removing the supply line from the oil reservoir and the delivery line, which leads to the carburetor, both lines must Supply line Delivery line be plugged with suitable plugs so that no. Mount the fixing bolts and tighten them crosswise.