John deere manual for lt155. John Deere LT133, LT155 & LT166 Lawn Tractors Service Repair Technical Manual 2019-02-01

John deere manual for lt155 Rating: 4,5/10 192 reviews

Operating

john deere manual for lt155

Push and hold brake pedal A down. Drive forward onto heavy-duty trailer. Brake pad must seat against top of sheave. Block mower blade with a piece of wood to prevent it from spinning. Thanks again and don't hesitate to participate in any topic that you are interested in here regardless of which forum it's in. I was just glad I got it out.

Next

Used John Deere LT155 for sale

john deere manual for lt155

See Parking Safely in the Safety Section. Carefully hold blade with glove, use a hand torque wrench, and tighten bolt to 57 N路m 42 lb-ft. 路 Disengage the mower before backing up. Before adjusting or servicing mower: 路 Disconnect spark plug wire s to prevent engine from starting accidently. Thanks Bob for your very thorough documentation of this job.

Next

Operating

john deere manual for lt155

To travel forward: M99486 1. If blades are out of time, set blades to proper timing. 路 Check the timing belt for damage and proper tensioning. 路 Always wear gloves when handling mower blades or working near blades. Dull blades will tear grass; tips of grass will then turn brown.

Next

Used John Deere LT155 for sale

john deere manual for lt155

The piece of metal the battery sits on is right over that ring. Put the lift lever in the mowing position before removing or installing the mower. 路 48C: 37 N路m 27 lb-ft. Loosen and remove cap screw A , hardened washer B , blade washer C and blade D. Use your 13mm socket to remove the tensioner idler sheave then remove the guide from the tensioner pulley to free the belt from the tensioner assembly. Mulch leaves several times if needed.

Next

Download John Deere LT133 LT155 LT166 Tractor PDF Manual

john deere manual for lt155

Remove wood blocks from both sides of mower. Before backing up, carefully check the area around the machine. Install the fixed idler assembly on the stud of the left support plate as you wrap belt loop around left spindle sprocket P. Put lift lever in transport position. See Parking Safely in Safety Section. Rotate right spindle sheave clockwise and observe that belt is riding properly in sprockets and idlers. Use a 13mm socket to loosen the nut and try not to lose the bushing that the spring hooks to.

Next

Used John Deere LT155 for sale

john deere manual for lt155

Do not run an engine in an enclosed area without adequate ventilation. Thanks again for purchasing John Deere equipment and being a part of our family. It will help you understand, care for, and lower the repair and maintenance cost for your lawn tractor. 路 Allow fresh outside air into the work area to clear the exhaust fumes out. Move lift lever to mowing position and make sure mower engagement lever is pulled back into stop position.

Next

Operating

john deere manual for lt155

Block mower blade with a piece of wood to prevent spinning and tighten cap screws to 53 N路m 39 lb-ft. How do I put fluid back in it? Instead of cutting a notch in my battery tray, I just took a good pair of vise grips and bent it up some to be able to access the snap ring more easily. Move lift lever to mowing position and move to left side of mower. Put lift lever in the mowing position. Put lift lever in mowing position. The tension pulley is bolted through a slot in the tension arm, and I think this is so you can fine tune the belt tension by moving the pulley back and forth along the slot.

Next

Operating

john deere manual for lt155

Block mower blade with a piece of wood to prevent spinning and tighten cap screw to 68 N路m 50 lb-ft. Incorrect belt tensioning can cause belt damage. It made a whining noise. Not sure how to get to the snap ring on the top of the sector gear though. This lubrication is to prevent rusting and seizing. There were no wires below the button that fell down.

Next