Not onlv is it im~ortantto make sire the oil is at t k proper level not above or below , but it is important to check the oil for signs of contamination from moisture. Check fuel and replace, if necessary. If we can provide additional assistance of any kind please feel free to and tell us what you need. Clean by rinsing in clean lead-free gasoline or kerosene. Check - Air vent must be open all-the-way and free from restrictions.
Tighten cover or replace gasket. Remove the two screws securing the lower unit to the exhaust housing. Check cowl air inlet and carburetor for obstructions. Outboard will not start 9. Copyright 2019 Marine Service Manuals. Reset float to correct level.
If necessary for service or overhaul, drain the gear oil from the To install: 7. Customer Service Evinrude Outboard Motor Service Manuals - Marine Service Manuals has made every effort to make your Evinrude Outboard Motor Service manual shopping experience as easy as possible. How to change oil on 2010 mercury 130 hp outboard motor how to drain oil on 1982 mercury 130 hp 99 marine outboard 2011 johnson 130 hp outboard 4 cycle repair manual 1984 johnson 130 hp outboard manual 1985 mercury 130 hp outboard high pressure fuel filter 2012 mercury 130 hp outboard valve cover gasket replace 1987 mercury outboard 130 hp fuel pressure regulator no spark 2013 130 hp mercury outboard oil injection on 1990 yamaha 130 hp outboard. Consider using a digital camera if available to help document assemblies during the removal and disassembly procedures. You can pay for your Evinrude Outboard Motor Service manual with Paypal or Visa, MasterCard or Discover. After downloading your Evinrude Outboard Motor Service manual you can view it on your computer or print one or all of the pages needed. Improperly mixed fuel; contaminants water, dirt, etc.
Testing Install clear fuel hose s between fuel pump and carburetor s. Lubrication, the use of high-quality oils 2- stroke or 4-stroke and proper fuelioil ratios 2-stroke or frequent oil inspectionlchanges 4-stroke are the most important ways to preserve powerhead condition. You can compare the major components of an outboard with the engine and drivetrain of your car or truck. Performing the scheduled maintenance is very important. If you suspect water in the gearcase, start by draining and closely inspecting the fluid refer to the procedures found in the Maintenance and Tune-Up section. The subsequent pages give detailed procedures. Air leakage into fuel system.
The Johnson-Evinrude Workshop manual downloads for the above listed models describes the service procedures for the complete vehicle. Remove any sand, silt or dirt that could potentially damage seals or clog passages. Anti-Siphon valve restricting fuel flow. In doing so, the powerhead is the equivalent of the engine and the gearcase is the equivalent of your drivetrain the the power necessary to move the'vehicle, while the gearcask is thk assembly that transmits that power via gears, shafts and a propeller instead of tires. But both DlYers and professionals must know their limits.
If, it is found that the anti-siphon valve is the cause of the problem, either 1 replace the anti-siphon valve or 2 replace it with a solenoid-operated fuel shutoff valve. Loss of fuel pump pressure 2. Restricted fuel flow to carburetor. Air leaks past mixing chamber cover. This website is not associated with the product manufacturer in any way. This is not because they are not capable of the task, but because that's what a machinist does day in and day out. Run engine, and inspect fuel passing thru hose s for air bubbles.
Thoroughly inspect the gearcase and exhaust housing for signs of damage. If any oil leaks out or water enters, either the propeller shaft seal must be replaced or the gearcase must be disassembled, inspected and completely overhauled. Check fuel lines and filter s for restricted flow. It compensates for the initial wear that occurs during the life of the outboard motor. Blow out with compressed air.
Evinrude Outboard Motor Service manuals are available for immediate download! Fuel tank air vent closed or restricted. A crack in the fuel pick-up outlet tube located in fuel tank. A needle stuck closed, will prevent fuel from entering carburetor. If, after using a separate fuel supply, it is found that the anti-siphon valve is the cause of the problem, there are 2 solutions to the problem; either 1 remove the anti-siphon valve or 2 replace it with a solenoidoperated fuel shutoff valve. You can pay for your Johnson Evinrude Outboard Motor Service manual with Paypal or Visa, MasterCard or Discover.
Some symptoms of restricted lean fuel flow, are: 1. We will also send you an email with a copy of your Evinrude Outboard Motor Service manual download link. Check, replace, or clean all fuel filters. Repair type of oil for a 2002 mercury outboard 130 hp engine what is the float setting on a 1993 yamaha 130 hp out board what should the compression be on a 1994 mercury 130 hp outboard when should the timing belt be replaced on a 1995 mercury 130 hp outboard motor 1996 yamaha 130 hp gear case 1997 yamaha 130 hp timing adjustment yamaha 1998 130 hp carburetor yamaha 1999 130 hp carburetor 2000 johnson outboard 130 200 225 130 hp 90 degree v models service manual. Vapor lock Any type of anti-siphon device must be located between the outboard fuel inlet and fuel tank outlet. These days, many professionals will leave portions of machine work from cylinder block and piston disassembly, clean and inspection to honing and assembly up to a machinist.