Minor deviations resulting from enhancements to the motorcycle design cannot be entirely precluded. This warranty extends to the first person who buys this exhaust system for purposes other than resale, and to all subsequent buyers. Be sure to have the workshop verify all service work carried out in the service manual to avoid losing your right to claim under the warranty. You are now the owner of a state-of-the-artsport motorcycle that guarantees to bring you lots of fun and enjoyment, provided that you clean and maintain it appropriately. Simply press on the filler cap to close. Start the engine, allow to run warm for 4 minutes and switch off the engine.
These problems or conflicts can be avoided if the motorcycle is used responsibly. Do not mix this oil with any other hydraulic oil. Mount the oil drain plug on the oil tank with a new seal ring and tighten to 20 Nm. Please insert the serial numbers of your motorcycle in the boxes below: Frame number Stamp of dealer Engine number Key number All information contained is without obligation. The speed limiter will set in at 9600 rpm, drastically reducing the engine power above this rotational speed.
Make sure it is standing securely on a firm surface. The engine will overspeed, damaging the valves. . The Owner's Manual is an integral part of the motorcycle and must be handed over to the new owner when the motorcycle is sold. We have provided a table with pragmatical values to help you tune up your motorcycle. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. Slightly depress the bulb, turn it approx.
It will go out when the gasoline pressure is high enough. Just in case, you can also put in a gear. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. The designation low and high-speed refers to the movement of the shock absorber and not to the motorcycle's driving speed. The ignition key can be pulled out to open the other filler cap. The side stand is linked to the safety start system; follow the driving instructions.
If the compen- sating tank is empty, also check the cooling liquid level in the radiator. The side stand is linked to the safety start system;. These tune-up specifications are reference values only and should serve as a basis for your per- sonal chassis and suspension tuning. Check the engine oil level or contact a ktm workshop. Replace a blown fuse only with an equivalent one. Socket for electric accessories A socket is provided in the cockpit for electric accessories, e.
The illustrated models partly contain extra equipment, which is not applied to standard models. When the lowest bar lights up, the cooling liquid has reached a temperature 100°C 212°F of approx. To open, insert the ignition key, turn 45° in a clock- wise direction and fold up the filler cap. This allows you adjust the damping behavior to match your driving style and the payload. Remember that electric accessories will run down the battery.
This is the only place that has the qualified technicians and the special tools required for the 990 Adventure. The green indicator lamp will light up when the gearbox is in an idling position. The dis- play can be adapted to the respective country on long-distancetrips. A loose axle passage can cause the motorcycle's handling performance to become instable. The orange warning lamp fuel injection briefly lights up when the ignition is switched on. You can have the speed and distance shown in kilometers or miles in the display. Thoroughly clean the drain plugs, the cover and both oil screens.
You are now the owner of a state-of-the-art sport motorcycle that guarantees to bring you lots of fun and enjoyment, provided that you clean and maintain it appropriately. Storage temperature 0 - 35°C 32 - 95°F , avoid direct sunlight. To lock, close the cover, insert the quick release in the dolly and turn 180° in a clockwise direction. Otherwise, the owner may become subject to penalties under state and local ordinances. The clutch is hydraulically actuated and adjusts itself automatically. Ignition off, engine can't be started Ignition on, engine can be started Ignition off, handlebar blocked To switch the ignition to position turn the ignition key to position and firmly press it 1 into the lock.
Turn the handlebar to the left, then turn the ignition key to the left. Excessive pressure in the interior of the fork can cause leaks in the fork. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. When the lowest bar lights up, the cooling liquid has reached a temperature of approx. Use of the motorcycle under extreme conditions, e. Disconnect the fuel lines, disconnect the connector for the fuel pump and the pickup cable fuel level and set down the tank. Tighten the screws to 6 Nm.
Tightening the screws and nuts too tightly can damage the thread and components. Add cooling liquid until it runs out of the discharge opening without bubbles and immedi- ately mount the screw to prevent more air from getting into the radiator. This allows you adjust the damping behavior to match your driving style and the payload. The green indicator lamp will light up when the gearbox is in an idling position. This manual should be kept near the machine for reference and periodically reviewed by all personnel who will come into contact with it.