Troy bilt tb20cs manual. Troy 2019-01-25

Troy bilt tb20cs manual Rating: 9,9/10 235 reviews

Troy

troy bilt tb20cs manual

Keep tension on the cord and slowly let it recoil around the pulley. Rocker Switch Spark Plug Gap. The 2000 and later small off-road engines are warranted for two years. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. . Reinstall the starter housing, clutch housing, drum, rotor, ignition and throttle wires. Our goal is to get you the Troy-Bilt parts you need as quickly as possible.

Next

Warning, Maintenance and repair instructions

troy bilt tb20cs manual

Also included may be hoses, belts, connectors and other emission-related assemblies. Failure to maintain bump knob counterclockwise Fig. . This is often mistaken for an out of adjustment carburetor. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. Make sure you are in the starting position when pulling the starter rope Fig.

Next

Warning, Maintenance and repair instructions

troy bilt tb20cs manual

Refer to Oil and Fuel Information. Start the engine and let it run at a high idle for a minute to warm up. Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and catalytic converter. We are waiting to assist you! This lightweight, versatile weed eater is great for homeowners looking to trim the edges of their lawn. Never o perate theunit attachment when it is rotating. Our show parts photos for your selection.

Next

How to Repair a Troy

troy bilt tb20cs manual

Replace it if it is damaged, or if you are unable to clean it thoroughly. Locate the muffler, but do not remove it. Cast iron transmissions, simple easy to maintain linkage and construction, and high performance has made Troy-Bilt a household name. Never r emove t hecapofthefueltank,or moving parts, Do not touch or try to stop the cutting addfuei,when theengine ishot. Slowly pull part of the shaft out from the engine until you can access the ignition and throttle wires. Clean Air Filter The condition of the air filter is important to the operation of the unit. Do not let the pulley spin free.

Next

Troy Bilt Parts

troy bilt tb20cs manual

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-520-5520. Reinstall the two hood tabs into the two muffler slots and flip the spark arrestor hood closed. Adjust Idle Speed Screw If, after checking the fuel mixture and cleaning the air filter, the engine still will not idle, adjust the idle speed screw as follows: 1. Refer to Air Filter Maintenance. . The manufacturer is not liable to cover failures of warranted parts caused by the use of add-on or modified parts.

Next

Troy Bilt Parts

troy bilt tb20cs manual

Check the condition of the air filter before adjusting the idle speed screw. This operator's manuaH provides you with easy-to-. Warranty services or repairs will be provided at all Authorized Troy-Bilt Service Centers. Two tabs act as hinges on the right side of the hood. Today there are also push mowers, self-propelled mowers, riding mowers, log splitters, snow blowers, pressure washers, generators and many more products that proudly wear the Troy-Bilt name.

Next

Troy

troy bilt tb20cs manual

Wear protective clothing and observe all safety instructions to prevent serious personal injury. Clean the spark arrestor screen with a wire brush. Reconnect the shaft to the engine and the throttle housing to the shaft. Reinstall the spark arrestor screen snugly back into the spark arrestor hood. Flip open the spark arrestor hood like a door and then pull its tabs out of the muffler slots. Drain and refill the tank with fresh, properly-mixed fuel prior to making any adjustments.

Next

How to Repair a Troy

troy bilt tb20cs manual

Carefully pry up the left side spark arrestor hood. . We offer cheap shipping rates and quick service to help keep your equipment in good running order. Good equipment deserves good parts and TroyBiltPartsOnline. An authorized service dealer should make carburetor adjustments. Replace the screw you removed in Step 2 and tighten it securely. Before winding, split the line back about 6 inches.

Next